产品概述

GGD型交流低压配电柜于固定接线低压配电柜。用于发电厂、交电站、厂矿企业等电力用户，作为交流50-60HZ，额定工作电压380V、额定工作电流至3150A的配电系统中，作为动力、照明及配电设备的电能转换，分配与控制之用。

产品具有分段能力高，动热稳定性好，结构新颖、合理、电气方案切合实际，系列性使用性强，防护等级高等特点，可作为更新换代的产品使用。

Description

GGD type AC low-voltage distribution cabinet was developed in1991.It is a nationallow-voltage distribution cabinet. Itis divided into ggd1/ggd2/ ggd3,with different current capacity. (hereinafter referred to as distribution cabinet) is used for power users of power plants, transportation power stations.factories and mining enterprises, etc. as the power distribution system with AC 50-60Hz, rated working voltage 380V,rated working current to 3150A, asthe power conversion, distribution and control of power, lighting and distribution equipment.

The product has high segmentation ability, good dynamic and thermal stability, novel and reasonable structure, and practical electrical scheme. It hasstrong seriality and usability. The protection levelis high. It can be used as a new product.

使用环境

• 环境温度不高于+40”C，不低于-5"C

• 产品安装使用时，使用地点的海拔高度不超过2000M。

• 周围空气相对湿度不大于90%(+259C).

• 设备应安装在无剧烈震动和冲击的地方，以及不足使电器元件受到腐蚀的场所。

• 周围空气相对湿度在最高温度40度时不超过5%，在较低温度时允许有较大的相对温度，应考虑到由于度的变化可能会偶然产生凝露的影响

• 设备安装在无剧烈震动和冲击的地方，以及不足使电器元件受到腐蚀的场所

• 用户有特殊要求时可与制造厂协商解决

Using The Environment

• The ambient temperature is not higher than +40"Cand not lower than-5*c.

• When the product is installed and used, the altitude of the place of use shall notexceed 2000m.

• The relative humidity of the surrounding airis not more than 90%(+25*0.

• The equipment shall be installed in the place without severe vibration and impact, and the place where the electrical components are not corroded.

• The relative humidity of ambient air shall not exceed 5% atthe maximum temperature of40C. Larger relative temperature is allowed at lower temperature,and the influence of occasional condensation due to the change of relative humidity shall be considered.

• The equipment shall be installed in the place without severe vibration and impact, and the place where the electrical components are corroded due to insuffcient equipment.

• If users have special requirements, they can negotiate with the manufacturer.

主要特点

◆按用途分为:受电柜、母线联络柜、馈电柜、电动机控制柜、无功功率补

偿柜、照明配电柜。

◆柜体结构: C型材组装,模数孔为E=25MM，产品装配的通用性高。

• @600MM至1200MM宽的柜、正面背面均采用对称的双门结构。

• 柜[ ]采用最新侧装铰链与C型材相连、安装、拆卸方便，门的折边处有加

• 强折弯工艺，保证强度的同时增加内部美观。

• 柜内的安装件与构架间用自攻螺钉紧固，拆装方便。

• 柜体的顶盖，使用铰链安装，顶盖可以开启，便于主母线的装配和调整。

Main Character

◆It can be divided into: receiving cabinet, bus connection cabinet, feeder cabinet,

motor control cabinet, reactive power compensation cabinet and lighting

distribution cabinet.

◆Cabinet structure: C profile assembly, module hole E=25mm, high universality

of product assembly.

• The cabinet with the width of 600mm to 1200mm adopts symmetrical double door structure on the front and back.

• The cabinet door adopts the latest side mounted hinge to connect with C profile, which is convenient for installation and disassembly. The folding edge of the door has a strengthened bending process to ensure the strength and increase the internal beauty.

• The installation parts in the cabinet and the frame are fastened with self tapping screws, which is convenient for disassembly and assembly.

• The top cover of the cabinet is hinged and can be opened to facilitate the　assembly and adjustment of the main bus。